Acroweld powerwagon build

Start your thread and show everyone your build out.
Post Reply
User avatar
SimonandSimonBeast
250_Posts
250_Posts
Posts: 416
Joined: Wed Nov 20, 2019 10:53 pm
Model Year: 2013
Location: Upper Salford, PA

Re: Acroweld powerwagon build

Post by SimonandSimonBeast » Thu Jan 16, 2020 5:01 pm

Impressive. Looks familiar. You're truck's twin is here in PA minus the sweet bumper. Nice job. I lucked out with none of my bolts seized, but def know the challenge from prior rigs. BTW I was able to sneak in the new Thuren springs without a compressor. I had to pull my 3 ton jack out from under the center, use it to push up on one knuckle, install spring on opposite side and then vice versa. I did this with OE swaybar links removed. When you push up on one side you can get the other side to dip plenty further. This is exactly why these solid axle trucks are better at keeping the wheels on the ground, especially when the swaybar is disconnected.

Sent from my Moto Z (2) using Tapatalk

:rockon: :chug:
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Thu Jan 16, 2020 5:14 pm

I drove around with no sway bar drop links for 2 months and it was so smooth. I had to put the links on for a highway trip this weekend.


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
PWJouster
250_Posts
250_Posts
Posts: 466
Joined: Wed Dec 27, 2017 8:44 am
Model Year: 2018

Re: Acroweld powerwagon build

Post by PWJouster » Fri Jan 17, 2020 8:08 am

3.0 kings and youll never need a sway bar again!
2018 Powerwagon-6.4 Hemi
Nanny kill switch and Locker Bypasses
Thuren Tuned King 3.0 & 2.5 Pintop Stage 3/2
17 Method NV-Toyo RT 37
Evo On-Demand Air Swaybar Disconnect
S&B Intake-Mufflex-Magnaflow/resonator delete
SPOD Bantam
On-Board air ARB CKMTA12
Baja design and Rigid Industries
Purple Cranium Spider dif guards
Pedal Commander
Top
User avatar
Oilbrnr
50_Posts
50_Posts
Posts: 164
Joined: Tue May 02, 2017 7:26 pm
Model Year: 2016
Location: Flagstaff & Scottsdale, Arizona

Re: Acroweld powerwagon build

Post by Oilbrnr » Fri Jan 17, 2020 9:37 am

PWJouster wrote: ↑
Fri Jan 17, 2020 8:08 am
 3.0 kings and youll never need a sway bar again!
Better (and much cheaper) yet, get Able Components (David) locker/swaybar bypass kit. Plug-n-play. :wink:
'16 with '17 FWC
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Fri Jan 17, 2020 6:23 pm

Long arms first then Deavers then Kings


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
PWJouster
250_Posts
250_Posts
Posts: 466
Joined: Wed Dec 27, 2017 8:44 am
Model Year: 2018

Re: Acroweld powerwagon build

Post by PWJouster » Mon Jan 20, 2020 7:14 am

Oilbrnr wrote: ↑
Fri Jan 17, 2020 9:37 am
PWJouster wrote: ↑
Fri Jan 17, 2020 8:08 am
 3.0 kings and youll never need a sway bar again!
Better (and much cheaper) yet, get Able Components (David) locker/swaybar bypass kit. Plug-n-play. :wink:
truth be told, understandable statement... i have an air release and while i typically switch it off for slow going anywhere, i need my factory sway bar for throwing the truck around on the road.

anyone can benefit from 3.0 kings though....they serve a different purpose(boogie-rated)
2018 Powerwagon-6.4 Hemi
Nanny kill switch and Locker Bypasses
Thuren Tuned King 3.0 & 2.5 Pintop Stage 3/2
17 Method NV-Toyo RT 37
Evo On-Demand Air Swaybar Disconnect
S&B Intake-Mufflex-Magnaflow/resonator delete
SPOD Bantam
On-Board air ARB CKMTA12
Baja design and Rigid Industries
Purple Cranium Spider dif guards
Pedal Commander
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Fri Mar 20, 2020 9:29 am

Image
Image
Image
Image
With all this time at home I finally finished my bumper. Added stiffeners and finished the wheel well corners along with drilling mounting holes. Still haven’t got pictures fully mounted. Tubing is in the garage for the rock sliders. California is under a stay at home order so I’ll be working on my truck quite a bit.


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
Hbpwagon
Posts: 12
Joined: Mon Oct 28, 2019 7:37 pm
Model Year: 2015

Re: Acroweld powerwagon build

Post by Hbpwagon » Sun Mar 22, 2020 7:52 pm

Looking good.
I know what you mean about the spare time. I’m just about done with home projects then I can start on the truck stuff.
Enjoy shelter at home. 😀
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Thu Mar 26, 2020 12:26 am

Image
Image
Little day trip with the family. Pozo summit, California


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
Mule007
500_Posts
500_Posts
Posts: 689
Joined: Mon May 16, 2016 9:27 pm
Location: Colton, Oregon

Re: Acroweld powerwagon build

Post by Mule007 » Thu Mar 26, 2020 9:11 am

That bumper looks good 👍
:patriot:2005 Mineral Grey; QC- #0666: "Laramie", power heated Leather seats, tow mirrors, dual zones, Alpine 9 speaker surround sound, steering wheel cruise control, music & volume controls; remote start, 6 CD player, AC; dark charcoal silver interior.
Additions: Frame mounted .188 DOM 3" steel rock rails, low profile steps;1.5” Skyjacker leveling kit; Bully Dog GT Platinum A-pillar mount programmable performance chip, monitor,& tuner; Linex Platinum OTR HD bed & rock panel coating; Red Ryder matching cab high fiberglass canopy; 2” Linex brush guard w/4-4” Halogen off road lights; Hopkins Trailer Mate brake controller; Bearcat Pro 68XL CB; Mopar black fender flares; PW winch accessory kit/remote control.
Tools: hand tools, 60” Extreme High Lift; rigging; straps; shackles; F&R chains; (2ea) rear wheel well NATO 20 L narrow gas cans & 5# extinguishers
Updates: Jasper Remfgr’d 5.7 Hemi Engine; Open Range AT 35x12.5 x17 MP3 10 ply E tires; Moog HD U/L front axle ball joints & wheel bearings; new link, sway, y bar & bushing assemblies; fuel pump; A/C exhaust fan & compressor;1 ton HEMI transmission cooler; OEM radiator; front pinion seal & bearing; Denso 180-amp alternator; Megatron 850 CCA HD battery; water pump, serpentine belt, Bilstein 2 5100 shocks/HD steering damper; F&R locker motors,sensors/u joints; 3" Magna flow cat back rear exit dual exhausts; Performance Brake/slotted rotor/caliper/pads
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Acroweld powerwagon build

Post by Pasopwagon » Thu Mar 26, 2020 9:41 am

Thanks mule
Synthetic line or steel cable? The cable that came on the truck needed to be replaced what are thoughts?


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Tue Mar 31, 2020 10:34 pm

Image
Rock sliders moving right along


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
Mule007
500_Posts
500_Posts
Posts: 689
Joined: Mon May 16, 2016 9:27 pm
Location: Colton, Oregon

Re: Acroweld powerwagon build

Post by Mule007 » Tue Mar 31, 2020 11:01 pm

👍, looking good !
:patriot:2005 Mineral Grey; QC- #0666: "Laramie", power heated Leather seats, tow mirrors, dual zones, Alpine 9 speaker surround sound, steering wheel cruise control, music & volume controls; remote start, 6 CD player, AC; dark charcoal silver interior.
Additions: Frame mounted .188 DOM 3" steel rock rails, low profile steps;1.5” Skyjacker leveling kit; Bully Dog GT Platinum A-pillar mount programmable performance chip, monitor,& tuner; Linex Platinum OTR HD bed & rock panel coating; Red Ryder matching cab high fiberglass canopy; 2” Linex brush guard w/4-4” Halogen off road lights; Hopkins Trailer Mate brake controller; Bearcat Pro 68XL CB; Mopar black fender flares; PW winch accessory kit/remote control.
Tools: hand tools, 60” Extreme High Lift; rigging; straps; shackles; F&R chains; (2ea) rear wheel well NATO 20 L narrow gas cans & 5# extinguishers
Updates: Jasper Remfgr’d 5.7 Hemi Engine; Open Range AT 35x12.5 x17 MP3 10 ply E tires; Moog HD U/L front axle ball joints & wheel bearings; new link, sway, y bar & bushing assemblies; fuel pump; A/C exhaust fan & compressor;1 ton HEMI transmission cooler; OEM radiator; front pinion seal & bearing; Denso 180-amp alternator; Megatron 850 CCA HD battery; water pump, serpentine belt, Bilstein 2 5100 shocks/HD steering damper; F&R locker motors,sensors/u joints; 3" Magna flow cat back rear exit dual exhausts; Performance Brake/slotted rotor/caliper/pads
Top
User avatar
Mule007
500_Posts
500_Posts
Posts: 689
Joined: Mon May 16, 2016 9:27 pm
Location: Colton, Oregon

Re: Acroweld powerwagon build

Post by Mule007 » Tue Apr 07, 2020 3:54 pm

I sill have steel cable, but think quite a few have switched to synthetic but not certain of best synthetic brands, strength, etc. Believe main advantage is weight & possibly more length. Others can advise better
:patriot:2005 Mineral Grey; QC- #0666: "Laramie", power heated Leather seats, tow mirrors, dual zones, Alpine 9 speaker surround sound, steering wheel cruise control, music & volume controls; remote start, 6 CD player, AC; dark charcoal silver interior.
Additions: Frame mounted .188 DOM 3" steel rock rails, low profile steps;1.5” Skyjacker leveling kit; Bully Dog GT Platinum A-pillar mount programmable performance chip, monitor,& tuner; Linex Platinum OTR HD bed & rock panel coating; Red Ryder matching cab high fiberglass canopy; 2” Linex brush guard w/4-4” Halogen off road lights; Hopkins Trailer Mate brake controller; Bearcat Pro 68XL CB; Mopar black fender flares; PW winch accessory kit/remote control.
Tools: hand tools, 60” Extreme High Lift; rigging; straps; shackles; F&R chains; (2ea) rear wheel well NATO 20 L narrow gas cans & 5# extinguishers
Updates: Jasper Remfgr’d 5.7 Hemi Engine; Open Range AT 35x12.5 x17 MP3 10 ply E tires; Moog HD U/L front axle ball joints & wheel bearings; new link, sway, y bar & bushing assemblies; fuel pump; A/C exhaust fan & compressor;1 ton HEMI transmission cooler; OEM radiator; front pinion seal & bearing; Denso 180-amp alternator; Megatron 850 CCA HD battery; water pump, serpentine belt, Bilstein 2 5100 shocks/HD steering damper; F&R locker motors,sensors/u joints; 3" Magna flow cat back rear exit dual exhausts; Performance Brake/slotted rotor/caliper/pads
Top
Colibri
1000_Posts
1000_Posts
Posts: 1713
Joined: Mon Jun 08, 2015 5:44 pm
Model Year: 2009

Re: Acroweld powerwagon build

Post by Colibri » Fri Apr 10, 2020 12:55 am

Nice build you have going sir! I may have missed it, but what are you planning on using the winch for? On my truck and other vehicles I use for working I stay with wire rope because it’s more tolerant of abrasion and heavy use, on vehicles that are more off-road fun oriented I use synthetic because it’s light and strong and if I’m using it to get unstuck or to unstick someone else I’m more likely to be pulling in less than ideal conditions or angles etc. and synthetic is way less likely to kill or injure anyone if something goes sideways.
Central Texas and Houston area
2009 5.7 auto quadcab
Carli 3” coils deaver leafs 3” kings with 4 tube bypass rear and fr/rr hydro bumps
Howe steering pump and gear with hydraulic ram assist
Custom tube bumpers and white knuckle sliders
Creative fab trussed axle. rem polished and cryoed 5.13 gears with arb lockers fr/rr
Sharadon stage 2 545rfe with 3000 stall edge converter
Lots of other stuff lol
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Fri Apr 10, 2020 1:00 am

I went with the cable. I use it for work and play. Thank you for the feedback.


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
Osansux
Posts: 1
Joined: Fri Apr 19, 2019 11:31 pm
Model Year: 2018

Re: Acroweld powerwagon build

Post by Osansux » Tue Apr 14, 2020 12:51 pm

Good looking truck. I actually grew up just north of Paso and went to high school there. Mine is due for tires. How do you like 37s? I was planning on 35s since I tow a camper.
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Fri Apr 17, 2020 9:04 pm

Threw in some Synergy HD ball joints apparently the owner before me got into some water so I changed the front diff fluid too. It pays to have a nice ball joint press. Those things were frozen in from the years in the snow. I’m glad to give her a nice life in California. While everything was apart I took a wire wheel to much of the parts and then prime and painted them.


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Fri Apr 17, 2020 9:08 pm

Image
Image
Image
Image
Image


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
RustyPW
2000_Posts
2000_Posts
Posts: 5439
Joined: Thu May 24, 2012 4:23 pm
Model Year: 2008
Location: Brownsville Pa.

Re: Acroweld powerwagon build

Post by RustyPW » Fri Apr 17, 2020 10:39 pm

hmmmm........green milk. :chug:
PWOC #53
2008 POWER WAGON RC

My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826 :cash: :cash:

Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.

Russ
NRA - Benefactor, Golden Eagle. :lockedandloaded:
Top
User avatar
SimonandSimonBeast
250_Posts
250_Posts
Posts: 416
Joined: Wed Nov 20, 2019 10:53 pm
Model Year: 2013
Location: Upper Salford, PA

Re: Acroweld powerwagon build

Post by SimonandSimonBeast » Sat Apr 18, 2020 10:10 am

Looks like this stuff...Image

Sent from my Moto Z (2) using Tapatalk

:rockon: :chug:
Top
User avatar
olyelr
2000_Posts
2000_Posts
Posts: 3658
Joined: Sun Dec 07, 2014 9:00 pm
Model Year: 2016
Location: Kewadin, MI

Re: Acroweld powerwagon build

Post by olyelr » Wed Apr 22, 2020 8:13 am

Pasopwagon wrote: ↑
Fri Apr 17, 2020 9:08 pm
Image


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com

Holy frikin wheel weights.


Truck is coming along!
2016 Ram Power Wagon Laramie - Granite Crystal Metallic - Ramboxes - 35” AT3W - TazerRAM

:patriot:
Top
User avatar
SimonandSimonBeast
250_Posts
250_Posts
Posts: 416
Joined: Wed Nov 20, 2019 10:53 pm
Model Year: 2013
Location: Upper Salford, PA

Re: Acroweld powerwagon build

Post by SimonandSimonBeast » Wed Apr 22, 2020 9:36 pm

Very clean. Love how everything is painted up. So many people just leave it all rusted up under there.

Sent from my Moto Z (2) using Tapatalk

:rockon: :chug:
Top
User avatar
Pasopwagon
Posts: 35
Joined: Fri Jun 14, 2019 8:14 pm
Model Year: 2013

Re: Acroweld powerwagon build

Post by Pasopwagon » Wed May 27, 2020 8:24 pm

Synergy MFG long arms. These things are amazing. Correcting angles all over. The first picture is stock the rest are of the long arms. All photos are at full droop. The ride quality is better than stock. Image
Image
Image
Image


2013 Power Wagon
San Luis Obispo County California
www.acroweld.com
Top
Dthomas87
Posts: 7
Joined: Thu May 09, 2019 5:42 pm
Model Year: 2013
Location: Portland, OR

Re: Acroweld powerwagon build

Post by Dthomas87 » Mon Jun 08, 2020 2:34 am

Awesome build! Would love to see the finished sliders. Looks like you got them mounted in the long arm pic.
How do you like the fox shock/ thuren combo? I'm torn on the overlands vs fox
Top
Post Reply

Return to “Member Builds”