This seems a little too good to be true. Anyone tried it? $149 & capabilities of actuating various sensors/solenoids.
Wonder if it'll read the C codes for the lockers & smartbar.
Anyone have any info on it?
https://www.videntstore.com/wholesale/v ... ysler.html
Search found 9 matches
- Tue Aug 24, 2021 6:31 pm
- Forum: Engine & Drivetrain
- Topic: Drbiii alternative??
- Replies: 1
- Views: 1693
- Sat Aug 21, 2021 7:18 pm
- Forum: Engine & Drivetrain
- Topic: Transfer case troubles
- Replies: 6
- Views: 3836
Re: Transfer case troubles
Oh ya, my front driveshaft had about 5k miles on it when i started the fiasco of transfer cases (new oem)
- Sat Aug 21, 2021 7:15 pm
- Forum: Engine & Drivetrain
- Topic: Transfer case troubles
- Replies: 6
- Views: 3836
Re: Transfer case troubles
I fixed this a long time ago, but never updated the resolution. I removed the front driveshaft, drove in 4x4 to rule out an out of balance driveshaft as the cause. Still leaked. The remanufacturer had sent me another seal, still leaked. Seal seemed pretty flimsy. I asked the remanufacturer if they'd...
- Sat Aug 21, 2021 5:41 pm
- Forum: Engine & Drivetrain
- Topic: PIDS list
- Replies: 1
- Views: 1633
PIDS list
Has anyone compiled a Pid list for our trucks? Specifically I'm looking for the rear locker actuator Pid.
2010 PW
2010 PW
- Mon Aug 02, 2021 3:29 pm
- Forum: Engine & Drivetrain
- Topic: Derale Engine Oil Cooler
- Replies: 0
- Views: 2163
Derale Engine Oil Cooler
can anyone post up any pictures of where they mounted their powered coolers? getting ready to mount 1 up on my 2010 & just curious about where others have mounted theirs. (my thought was to just mount it upfront of the condenser blocking some of that off, but understanding the blower would force air...
- Fri Nov 27, 2020 9:04 pm
- Forum: Engine & Drivetrain
- Topic: Transfer case troubles
- Replies: 6
- Views: 3836
Transfer case troubles
Wondering if anyone else has been having troubles with their front pto seal. I had to put a reman t-case in. (That in itself has been a nightmare, the first 2 I got, I didnt even put in because the 1st had a stripped drain plug, 2nd had stripped position sensor threads) I cut ties with that guy & tr...
- Wed Aug 12, 2020 9:29 pm
- Forum: Engine & Drivetrain
- Topic: Smoked a motor
- Replies: 10
- Views: 3441
Re: Smoked a motor
I bought my truck with pretty much this same problem. I did the work myself, but cam replacement & hellcat lifters (larger bearing less likely to fail) while youre there, might as we'll do a timing chain, water pump, & oil pump. As a note. I did not have to open the AC to do this. After pulling the ...
- Tue Aug 11, 2020 8:40 am
- Forum: Recovery Gear, Tools, Accessories Etc
- Topic: Air Coupler Protection
- Replies: 5
- Views: 6660
Re: Air Coupler Protection
thanks for the replies. I was out of service for a bit. I ended up doing something similar to TommyG's response. took a chair tip, drilled a hole at edge of the tip at a 45degr angle. threaded a keyring thru it & put a stainless cable from it to the coupler to make a leash for it. it does fit very s...
- Fri Aug 07, 2020 8:50 am
- Forum: Recovery Gear, Tools, Accessories Etc
- Topic: Air Coupler Protection
- Replies: 5
- Views: 6660
Air Coupler Protection
just put OBA on my truck, but am curious where various people located their air couplers & what you did to keep the dirt & grit out of them (i'm not wanting to mount the coupler under the hood & Due to my setup, the rear bumper is not a good solution). I found this from Wits end https://absolute-wit...