Head Gasket
Re: Head Gasket
So the truck is still idling rough. Haven't been able to figure out what the issue is.
- battery has tested fine
- all the fuel injectors have the same resistance (~12.5 ohms)
- throttle body is fine (replaced it with a new one and same result so old one is back on)
- intake manifold, map sensor and PCV valve have been replaced
- fuel rail pressure tested well at 58 PSI when charged and on
- unplugged and plugged back in all the harnesses and checked all the grounds
- Reloaded stock tune and started it with the same result
- Reloaded the Arrington performance tune
- checked all vacuum hoses and none of them are cracked or leaking
Any other thoughts from the group on what to test?
It is not throwing any P Codes or errors
The ABS and Brake lights are on buy don't have a tool to read that code, however wouldn't think that would have anything to do with idle.
The rough idle definitely sounds like it is a fuel air mixture issue
Sent from my SM-G935V using Tapatalk
- battery has tested fine
- all the fuel injectors have the same resistance (~12.5 ohms)
- throttle body is fine (replaced it with a new one and same result so old one is back on)
- intake manifold, map sensor and PCV valve have been replaced
- fuel rail pressure tested well at 58 PSI when charged and on
- unplugged and plugged back in all the harnesses and checked all the grounds
- Reloaded stock tune and started it with the same result
- Reloaded the Arrington performance tune
- checked all vacuum hoses and none of them are cracked or leaking
Any other thoughts from the group on what to test?
It is not throwing any P Codes or errors
The ABS and Brake lights are on buy don't have a tool to read that code, however wouldn't think that would have anything to do with idle.
The rough idle definitely sounds like it is a fuel air mixture issue
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
- Pit Slave
- Vendor
- Posts: 1486
- Joined: Thu May 17, 2012 11:12 am
- Location: Sandy, Utah.. Moab, Jersey, Space Station, Baja.....
Re: Head Gasket
Do you let it run for at least until the end of the warm up cycle? Aka cold start. Like how is it after 5 minutes of run time? The reason I ask is that there are two different mapping programs, one for warm up and one for run. Also I would put the original ignition wire and mag setup to eliminate that potential issue.
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
Nothing's more dead than a horse in a glue bottle.
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
- Retired BLM Rig
- 1000_Posts
- Posts: 1123
- Joined: Sun Jan 31, 2016 6:51 pm
- Model Year: 2008
- Location: State of Jefferson
Re: Head Gasket
It might be worth it to do a compression test, or at least put a vacuum gauge on it to see how the needle behaves.
If you give it some supplemental fuel (carb spray or propane) in the throttle body, does it smooth out and run perfect? That would help determine if it's a lean running condition. Also, try putting a stethoscope on each injector to see if you can hear them all clicking evenly. Do you have a scanner that reads live data (fuel trim or O2 feedback)? Just some thoughts off the top of my head.
Maybe that cam was bigger than you thought with lots of lope.
If you give it some supplemental fuel (carb spray or propane) in the throttle body, does it smooth out and run perfect? That would help determine if it's a lean running condition. Also, try putting a stethoscope on each injector to see if you can hear them all clicking evenly. Do you have a scanner that reads live data (fuel trim or O2 feedback)? Just some thoughts off the top of my head.
Maybe that cam was bigger than you thought with lots of lope.
2008 Quad Cab - Stock RTI = 655, curb weight = 6081 lbs. Abel Components Plug & Play Locker Bypass®, Abel Components Full SmartBar Bypass®, Abel Components Nanny Kill Switch®, 2000 Watt ProMariner TruePower Plus Pure Sine Wave Inverter, Trailer Hitch Storage, MOLLE Door Panels, Wilton Hitch Vice, Locking Under Seat Storage Drawer, Smittybilt 2781 Air Compressor, 14K PullPal, Hi-Lift First Responder Jack, 25' Jumper Cable System, Slip Yoke Eliminator in a Can, Evolution vs. God, Share the Umbrella, Make sure you're right with God before you meet him!
- coder
- 1000_Posts
- Posts: 1347
- Joined: Wed Jun 06, 2012 5:18 pm
- Model Year: 2007
- Location: Trabuco Canyon, CA
Re: Head Gasket
x2 on the compression test, loss of compression on even one cylinder can cause rough idling/stalling at low rpms.
Vehicle: 2007 Power Wagon Quad Cab - Factory Options (Inferno Red, Premium Cloth Bench Seat, Light Group, Automatic Transmission, Leather Steering Wheel)
Suspension: Carli 3" Hemi Coils, Carli Control Arms, Carli King 2.5 Pin-Tops, Carli Stainless Steering Stabilizer, Carli Trackbar | Synergy 1" Rear Shackle
Performance: Magnaflow Muffler | Magnaflow Y-Pipe
Wheels/Tires: Yokohama X-A/T 35x12.5x17
Steering/Drivetrain/Axles: Carli Front Diff Guard | Dynatrac Ball Joints | Mopar HD Steering Gear
Miscellaneous: Line-X Bedliner | Locker Bypass Switch | Mopar Rock Rails | Odyssey Extreme 65-PC1750T | Performance Friction Brake Pads | Weathertech Digital Fit Mats | Winch Thermal Protection Bypass
Suspension: Carli 3" Hemi Coils, Carli Control Arms, Carli King 2.5 Pin-Tops, Carli Stainless Steering Stabilizer, Carli Trackbar | Synergy 1" Rear Shackle
Performance: Magnaflow Muffler | Magnaflow Y-Pipe
Wheels/Tires: Yokohama X-A/T 35x12.5x17
Steering/Drivetrain/Axles: Carli Front Diff Guard | Dynatrac Ball Joints | Mopar HD Steering Gear
Miscellaneous: Line-X Bedliner | Locker Bypass Switch | Mopar Rock Rails | Odyssey Extreme 65-PC1750T | Performance Friction Brake Pads | Weathertech Digital Fit Mats | Winch Thermal Protection Bypass
- TrueCowboy426
- 250_Posts
- Posts: 322
- Joined: Mon May 21, 2012 9:00 pm
- Location: Woodstock, ON Canada
Re: Head Gasket
What does the truck run like off idle? Will it actually rev (I think auto's are limited to 4000 in N and P?) Is there anyway that you can two foot drive it and see if it will actually drive and rev under load? Do you have a heat gun that you can get the temperatures of the exhaust header at each cylinder? If you have one, get a buddy to keep the truck running and see if you can find a cold cylinder(s). I still think it is something electical, and maybe you have coil pack(s) that isn't firing. I chased a bad coil pack on my hemi swap and the only way I could find it was to find the cold cylinder. Not sure how these motors react with a dead cylinder on fuel injected, but carburated they can be down 1 cyl and you don't even hardly notice till you try to drive. Even down 2 cylinders it would idle at 800rpm relatively smooth.
Other than that, I'm back to saying the cam is out of time. Even 1 tooth off can cause weird crap/ I would try the heat gun and see if you can find a dead cylinder/coil pack first.
Another thing to try, is pull the vacuum line off the booster and see if it will stay running. My thinking on this is if the tune is way off (no way it should be) or the front O2's went bad (again no way they should have) the extra air will lean it out and maybe stay running. Pulling from my carb issues learning now lol.
Sorry for all the questions just having verbal diarhea going thru how I would diagnose it.
Other than that, I'm back to saying the cam is out of time. Even 1 tooth off can cause weird crap/ I would try the heat gun and see if you can find a dead cylinder/coil pack first.
Another thing to try, is pull the vacuum line off the booster and see if it will stay running. My thinking on this is if the tune is way off (no way it should be) or the front O2's went bad (again no way they should have) the extra air will lean it out and maybe stay running. Pulling from my carb issues learning now lol.
Sorry for all the questions just having verbal diarhea going thru how I would diagnose it.
2007 Dodge Power Wagon - Inferno Red Quad Cab, G56, KRC 210X cam, SRT8 JGC seats, 35x12.50 Toyo MT's, Offroad lights behind the grill, Warn wireless winch remote, Carli front Diff Guard, Carli Long Travel Air Bags, On board air complete w/ train horns, homemade hidden gooseneck hitch, Homemade locker bypass, upgraded Mopar steering box, Centerforce clutch
1998 Dodge 2500 Laramie, QCSB 4x4. 24V cummins, completely rebuilt chassis with '01 1500 body installed, full gauges, Edge drag comp box, +150hp injectors, performance 47re built by me, 35" Toyo MTs on 3rd gen wheels.
2002 Dodge Ram 1500 ST 4x4 Quad Cab 4.7L Bright Silver, HO Cams, 12,000 lbs Winch mounted behind bumper, 4.56's, 2500 factory tow hooks, 35x12.50 Toyo MT's, Air-Lift Ride Control bags, homemade hidden ball gooseneck hitch.
1987 W100 - carburated 5.7 Hemi/727 combo, 35" Toyo MT's. Ramcharger D44 w/ warn hubs, Warlock seats, 2nd gen center console
1987 Dakota - RCSB, 413 big block, LT headers.
And a few jeeps for good measure.
1998 Dodge 2500 Laramie, QCSB 4x4. 24V cummins, completely rebuilt chassis with '01 1500 body installed, full gauges, Edge drag comp box, +150hp injectors, performance 47re built by me, 35" Toyo MTs on 3rd gen wheels.
2002 Dodge Ram 1500 ST 4x4 Quad Cab 4.7L Bright Silver, HO Cams, 12,000 lbs Winch mounted behind bumper, 4.56's, 2500 factory tow hooks, 35x12.50 Toyo MT's, Air-Lift Ride Control bags, homemade hidden ball gooseneck hitch.
1987 W100 - carburated 5.7 Hemi/727 combo, 35" Toyo MT's. Ramcharger D44 w/ warn hubs, Warlock seats, 2nd gen center console
1987 Dakota - RCSB, 413 big block, LT headers.
And a few jeeps for good measure.
-
- Posts: 23
- Joined: Sun Sep 18, 2016 11:13 pm
- Model Year: 2010
- Location: Iowa
Re: Head Gasket
Might check all your pushrods and make sure you didn't have one slip out from under the rocker arm. I've also had one miss the lifter yet look like it was in the hole. The pushrods can be tricky to install even with the special tools to hold them in place. I started rolling the engine over by hand with the valve cover off so I can watch each valve open and close. Also I think even one tooth off on your timing and catastrophic engine damage will occur, so your timing is probably ok.
Re: Head Gasket
Thanks guys. Appreciate the other thoughts here. Have some more things to try this weekend.
On a side note started compression testing but had to stop with cylinder 1 as the tool wouldn't come out of the cylinder.
Turns out the o ring pushed it's way up on the tool. Need to work it out with pliers. Oh the fun.
I will get it fixed.
I did check out all injectors with a stethoscope and they all sound good.
Sent from my SM-G935V using Tapatalk
On a side note started compression testing but had to stop with cylinder 1 as the tool wouldn't come out of the cylinder.
Turns out the o ring pushed it's way up on the tool. Need to work it out with pliers. Oh the fun.
I will get it fixed.
I did check out all injectors with a stethoscope and they all sound good.
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
Re: Head Gasket
Time to get back to basics.
You have already checked / replaced a lot of parts .
Compression test would be good but I would do a couple of easier things first.
Check vacuum.
Check for misfires with scan tool.
Check sensor readings with scan tool....all of them. Is there some data that doesn't make sense?
Is there a missing ground wire somewhere? ABS and brake lights on. Maybe they are a clue ?
You have already checked / replaced a lot of parts .
Compression test would be good but I would do a couple of easier things first.
Check vacuum.
Check for misfires with scan tool.
Check sensor readings with scan tool....all of them. Is there some data that doesn't make sense?
Is there a missing ground wire somewhere? ABS and brake lights on. Maybe they are a clue ?
Re: Head Gasket
Ok I pulled most of the spark plugs and they looked good. I got to cylinder 6 and there is carbon on the spark plugs.
Thoughts on whether this could be the cause and what may be causing it?
Also pulled off the valve covers on that bank and all of the valves seem to be operating fine.
They all compress and release the same as the engine manually cranks.
Looking at the cylinder with a scope didn't show that it was wet and the plug is definitely carbon not oil.
Sent from my SM-G935V using Tapatalk
Thoughts on whether this could be the cause and what may be causing it?
Also pulled off the valve covers on that bank and all of the valves seem to be operating fine.
They all compress and release the same as the engine manually cranks.
Looking at the cylinder with a scope didn't show that it was wet and the plug is definitely carbon not oil.
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
Re: Head Gasket
Maybe the coil pack to #6 isn't working
Re: Head Gasket
Checked the resistance and it seems good but need to check spark.
I am not getting any codes or misfires. Need to test the compression on that cylinder but it will be about a week and a half because of travel.
Sent from my SM-G935V using Tapatalk
I am not getting any codes or misfires. Need to test the compression on that cylinder but it will be about a week and a half because of travel.
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
Re: Head Gasket
On my 88' Ford Ranger, I replaced the coil with a new Accel unit. Supposed to give much more spark. Truck failed in a week. Bad coil. Replaced with another new Accel coil. Failed in a week. Bought a Ford coil, no more problems. Lasted another 150k. What are the chances of getting 2 faulty coils ???
Re: Head Gasket
My guess on the plug is no compression or no spark.
- Pit Slave
- Vendor
- Posts: 1486
- Joined: Thu May 17, 2012 11:12 am
- Location: Sandy, Utah.. Moab, Jersey, Space Station, Baja.....
Re: Head Gasket
Like I said earlier, put the original coil packs on and go from there. At least you know that set was running fine. I know it's a bitch but you want to be 100% it's not the ignition system.
I myself don't like changing a lot of components at once. I like to change one thing the try it out. This way I can be sure what's going on or in this case what's not working instead of guessing what failed.
Sent from my XT1254 using Tapatalk
I myself don't like changing a lot of components at once. I like to change one thing the try it out. This way I can be sure what's going on or in this case what's not working instead of guessing what failed.
Sent from my XT1254 using Tapatalk
Nothing's more dead than a horse in a glue bottle.
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
Re: Head Gasket
She Breathes!
After going back to basics and deciding to check everything again I came across my rough idle issue.
When I reassembled the heads I apparently didn't seat the pushrod on cylinder 3's intake valve correctly and it wasn't opening the valve.
Put it all back together and now my truck is running. Of course life isn't that simple.
In drive it is running rough under load however I have narrowed that down to what I think is an oxygen sensor or catalytic converter problem.
Going to hopefully get that done next week and should be good to go.
I know I had checked all of the valves before I put it back together but feel a bit dumb that I didn't look at that sooner.
Oh well it is all learning. And damn have I learned a lot.
Sent from my SM-G935V using Tapatalk
After going back to basics and deciding to check everything again I came across my rough idle issue.
When I reassembled the heads I apparently didn't seat the pushrod on cylinder 3's intake valve correctly and it wasn't opening the valve.
Put it all back together and now my truck is running. Of course life isn't that simple.
In drive it is running rough under load however I have narrowed that down to what I think is an oxygen sensor or catalytic converter problem.
Going to hopefully get that done next week and should be good to go.
I know I had checked all of the valves before I put it back together but feel a bit dumb that I didn't look at that sooner.
Oh well it is all learning. And damn have I learned a lot.
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
-
- 2000_Posts
- Posts: 5440
- Joined: Thu May 24, 2012 4:23 pm
- Model Year: 2008
- Location: Brownsville Pa.
Re: Head Gasket
Hell of a learning curve.
PWOC #53
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
Re: Head Gasket
Hahahahahahaha. Yup. I never do things the easy way Russ. You know this.
Sent from my SM-G935V using Tapatalk
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
- Mr.Smith
- 1000_Posts
- Posts: 1131
- Joined: Wed Sep 04, 2013 6:36 pm
- Model Year: 2009
- Location: Fort Collins, CO.
Re: Head Gasket
Hell yeah! Good job figuring this one out Sir!
-
- 2000_Posts
- Posts: 5440
- Joined: Thu May 24, 2012 4:23 pm
- Model Year: 2008
- Location: Brownsville Pa.
Re: Head Gasket
Ain't that the truth. Like changing a flat tire, that's sitting on a tree stump, facing down hill, in the rain.pdavey wrote:Hahahahahahaha. Yup. I never do things the easy way Russ. You know this.
Sent from my SM-G935V using Tapatalk
PWOC #53
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
Re: Head Gasket
If there was a crowning achievement I am pretty sure that takes the cake. Thanks again Russ and Mike for that assist.
Sent from my SM-G935V using Tapatalk
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
-
- 2000_Posts
- Posts: 5440
- Joined: Thu May 24, 2012 4:23 pm
- Model Year: 2008
- Location: Brownsville Pa.
Re: Head Gasket
pdavey wrote:If there was a crowning achievement I am pretty sure that takes the cake. Thanks again Russ and Mike for that assist.
Sent from my SM-G935V using Tapatalk
PWOC #53
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
2008 POWER WAGON RC
My build thread. http://forum.powerwagonregistry.org/vie ... =13&t=2826
Moab '09, '10, '12, '14.
Rausch Creek - Summer '10, Spring-Fall '11, Spring '12, Summer '13, Summer '14, Summer '15, Summer '16, Summer '17, Summer '18, Summer '20, Summer '22,
AOAA Summer '19.
Russ
NRA - Benefactor, Golden Eagle.
Re: Head Gasket
She lives. The Power Wagon is working 100% now. I love the extra HP and torque.
The final problem was a problem I created after fixing the pushrod. When I put the valve cover back on I accidently switched the 5 & 7 cylinder ignition wires.
I spent the day tracing everything and found it.
Now it runs like it should.
I bought some magnaflow downpipes and cats so having those put on with new oxygen sensors. Will have the truck back tomorrow and likely retire the Challenger for the winter.
Thanks all for the support and help here. I learned a hell of a lot and am very happy to have accomplished all this.
Sent from my SM-G935V using Tapatalk
The final problem was a problem I created after fixing the pushrod. When I put the valve cover back on I accidently switched the 5 & 7 cylinder ignition wires.
I spent the day tracing everything and found it.
Now it runs like it should.
I bought some magnaflow downpipes and cats so having those put on with new oxygen sensors. Will have the truck back tomorrow and likely retire the Challenger for the winter.
Thanks all for the support and help here. I learned a hell of a lot and am very happy to have accomplished all this.
Sent from my SM-G935V using Tapatalk
2005 Dodge Power Wagon QC Black - "Laramie"
Performance Mods:
Performance Mods:
- Comp 260 Camshaft, Upgraded Valve Springs, Forged Push Rods, JBA Shorties, Airaid Cold Air Intake, Gibson Dual Cat Exhast (Side Swept), National Speed Custom Tune
- Kenwood KVT-719 w/ Garmin Navigation and Kenwood Rear Camera, JL Stealth Sub
- Carli Upper "Bomb Proof" Ball Joints, NAPA Lower Ball Joints, Thuren Adj Track Bar, Thuren Adjusted Fox Damper, T-Style Steering Upgrade, New Power Steering Pump, 2012 Power Steering Motor Upgrade, Thuren King 2.5 Custom Rear Shocks -Stage 1, Thuren Off-set Control Arms, Thuren King 2.5 Custom Front Shocks -Stage 2, 35x12.50x17 Nitto Trail Grappler (previous tires Cooper STT), Carli Front Dif Gard,
- KC LightBar Behind Tow Hooks Mount, 2 KC Slim Driving Lights, 2 KC Offroading Lights, Weatherguard Black Steel Truck Box, Winch TPS bypass, Warn Wireless Winch Module
- nts007
- 2000_Posts
- Posts: 2284
- Joined: Wed Dec 11, 2013 10:01 pm
- Model Year: 2008
- Location: Sask, Canada, Earth
Re: Head Gasket
Awesome bud!!! Happy to hear that it was simple and now you can enjoy your truck once again.
08 ctd--mini max--thuren 3" coils and LT Leaves--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--king 2.5"s--37" Hankook Dynapro MT--DOR Long arms--Custom emf track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist and so much more