Need CAD unit wiring diagram.

waldo · Post by **waldo** » Tue Jun 13, 2017 12:44 pm

I need to see if there is some positioning feedback wiring going back to some module or other.

I keep getting random 4WD shift in progress messages on the EVIC. Naturally the dealer can't duplicate it because it's random.

My guess is that it's not 100% in the disengaged position since it stops if you put it in and out of 4H.

Post by **Pit Slave** » Tue Jun 13, 2017 12:46 pm

There should be a sensor of some sort to create the feedback loop, telling whether it is engaged or not.

Yeah, I smoked 'em, sometimes you just gotta #sendit

Retired BLM Rig · Post by **Retired BLM Rig** » Wed Jun 14, 2017 11:25 pm

Post by **DamageWagon** » Thu Jun 15, 2017 12:34 am

BLM... If you ever leave us we will all return to the Stone Age...

Retired BLM Rig · Post by **Retired BLM Rig** » Thu Jun 15, 2017 1:29 am

I remember the Stone Age, we had some good rock crawling back then and fewer nannies to contend with. That's why I bought a dinosaur!

Post by **DamageWagon** » Thu Jun 15, 2017 11:42 am

waldo · Post by **waldo** » Mon Jun 19, 2017 6:13 pm

Update. Had the truck in for the trans recall and had them look at this issue while it was there. They found the drive train control module was bad. Last time I had them look it didn't have any stored codes, this time it did. Should be fixed now.

olyelr · Post by **olyelr** » Mon Jun 19, 2017 7:11 pm

So this is for a newer wagon then ('14+)?

waldo · Post by **waldo** » Mon Jun 19, 2017 7:30 pm

olyelr wrote:So this is for a newer wagon then ('14+)?

My 16, my 07 doesn't have all that garbage.

From what I gather, the module was sending out the wrong/bad voltage to a bunch of sensors it looks at.

It's been doing that on and off since it was new and it just didn't set any codes until recently.

NickTF · Post by **NickTF** » Tue Jun 20, 2017 8:49 am

Is anyone making a manual CAD engagement option for our trucks like those which exist for the older 2nd gen rams? My truck is a 2015 and it would be nice to have 2wd lo when at a boat ramp in the future.

olyelr · Post by **olyelr** » Tue Jun 20, 2017 2:26 pm

NickTF wrote:Is anyone making a manual CAD engagement option for our trucks like those which exist for the older 2nd gen rams? My truck is a 2015 and it would be nice to have 2wd lo when at a boat ramp in the future.

I have not seen a manual CAD kit for the new trucks yet, but they do have an electronic setup that makes the CAD not engage when putting it in 2 low.

Here is a thread I started a bit back about it, with a link to the kit...

http://forum.powerwagonregistry.org/vie ... kit#p76265

NickTF · Post by **NickTF** » Tue Jun 20, 2017 2:40 pm

^^^^buuuuuuTTTTTTfuuuuuul, thanks!

Power Wagon Registry

Need CAD unit wiring diagram.

Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.

Re: Need CAD unit wiring diagram.