Mopar rock rail install
Mopar rock rail install
Hi all. I've got a lead on some factory mopar rock rails for my gen3 that I'd like to buy and install. I've searched and found very little detailed information on installing. Most just mention drilling a dozen or so holes in the frame. ...does anyone have first hand experience or know where detailed instructions might be found? It says they come with all hardware and special tools.
Thanks!
Sent from my SM-G900T using Tapatalk
Thanks!
Sent from my SM-G900T using Tapatalk
Re: Mopar rock rail install
I haven't seen this topic come up in a long time. Rock rails were a very rare option. Might have been dealer installed even. Think they cost around $800+ . Don't remember if that was installed or just parts. The kit came with some very special bolts and fasteners to mount to frame for one time use. Those became impossible to get at some point. I believe the drilling came with homemade rails and a few aftermarket fabricators trying to make copies and using normal bolts/nuts. Basically a hard and expensive undertaking.
Sorry this isn't any help with your question but I'm sure someone has a better answer. Let's see what they have to say.
Sorry this isn't any help with your question but I'm sure someone has a better answer. Let's see what they have to say.
- Pit Slave
- Vendor
- Posts: 1486
- Joined: Thu May 17, 2012 11:12 am
- Location: Sandy, Utah.. Moab, Jersey, Space Station, Baja.....
Re: Mopar rock rail install
Let me see where mine are.
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
Nothing's more dead than a horse in a glue bottle.
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
There are two ways to conquer and enslave a nation.
One is by the sword. The other is by debt.
John Adams - 1826
I guess you could say I'm a bit off center.....
Re: Mopar rock rail install
I found somewhere that the special tools required are wire hangers and mounting brackets. Other than that I think it's just measuring and drilling. Thanks pit slave ....anything would be helpful.
Sent from my SM-G900T using Tapatalk
Sent from my SM-G900T using Tapatalk
Re: Mopar rock rail install
I have my instructions. I can try to upload them here later or send them to you in an e-mail.
Preview
2005 white Q.C. Power Wagon #1716
AEM Brute Force intake
Gibson CAT back exhaust
Super Chips Flashpac Tuner
Wet Okole seat covers
35" Nitto Trail Grappler Tires
Line-X bed coating
Trac Rac Sliding Lumber Rack
Dual Batteries w/ Hellroaring Technologies Isolator/Combiner
Extreme Outback Magnum on board air compressor
H2 rims
2005 white Q.C. Power Wagon #1716
AEM Brute Force intake
Gibson CAT back exhaust
Super Chips Flashpac Tuner
Wet Okole seat covers
35" Nitto Trail Grappler Tires
Line-X bed coating
Trac Rac Sliding Lumber Rack
Dual Batteries w/ Hellroaring Technologies Isolator/Combiner
Extreme Outback Magnum on board air compressor
H2 rims
Re: Mopar rock rail install
That would be great trk4sale! Thank you. Pm sent
Sent from my SM-G900T using Tapatalk
Sent from my SM-G900T using Tapatalk
Re: Mopar rock rail install
On the way!
Preview
2005 white Q.C. Power Wagon #1716
AEM Brute Force intake
Gibson CAT back exhaust
Super Chips Flashpac Tuner
Wet Okole seat covers
35" Nitto Trail Grappler Tires
Line-X bed coating
Trac Rac Sliding Lumber Rack
Dual Batteries w/ Hellroaring Technologies Isolator/Combiner
Extreme Outback Magnum on board air compressor
H2 rims
2005 white Q.C. Power Wagon #1716
AEM Brute Force intake
Gibson CAT back exhaust
Super Chips Flashpac Tuner
Wet Okole seat covers
35" Nitto Trail Grappler Tires
Line-X bed coating
Trac Rac Sliding Lumber Rack
Dual Batteries w/ Hellroaring Technologies Isolator/Combiner
Extreme Outback Magnum on board air compressor
H2 rims
Re: Mopar rock rail install
Thanks trk4sale. Those are very helpful! If I pick these up, I'll be sure to document all of the steps for future use.
Sent from my SM-G900T using Tapatalk
Sent from my SM-G900T using Tapatalk