3rd gen u joints

If it's about Power Wagons, all generations, this is where it'll go. This is the original PWR Forum Power Wagon Technical Discussion Section. And this includes everything that doesn’t fit in any one of the other categories related to the truck goes here!
Post Reply
gdane4x4
Posts: 20
Joined: Mon Jan 05, 2015 9:32 am

3rd gen u joints

Post by gdane4x4 » Fri Feb 19, 2016 8:51 am

Sorry guys for asking but have done tons of searching and different post and different sights show differnet part numbers. I know spicer changed some part numbers as well I think. Anyways looking for Spicer part numbers to replace and rebuild all joints in front drive shaft and also rear drive shaft. Spicer sealed no lube hds preferably. I have the axle joint number but confusing on the others. Also was going to give 8 lug a call possibly as well but figured you guys might uave them available. 2005 quad pw w one piece rear. Thanks in advance.

2011RPW
250_Posts
250_Posts
Posts: 278
Joined: Thu Oct 24, 2013 9:22 pm
Model Year: 2011
Location: Harper, TX

Re: 3rd gen u joints

Post by 2011RPW » Fri Feb 19, 2016 10:19 am

Email George or Tommy at 8Lug Truck Gear. They can help you out. You'll probably have to measure the joints on the double cardan since they seem to be different between trucks.
2011
Thuren 3" Suspension, 37' Toyo R/T's, S&B, Flowmaster, Diablo Trinity, N-Fab steps (junk), 31" LED Light Bar, Replacement Bumpers, debadged.

User avatar
GunniPWguy
500_Posts
500_Posts
Posts: 954
Joined: Fri May 25, 2012 11:52 am

Re: 3rd gen u joints

Post by GunniPWguy » Fri Feb 19, 2016 10:38 am

Check this site out. Lots of oem drivetrain parts
http://quad4x4.com/dodgeAAM925frontAxle.html
2005 Black Pow Wagon mods: DT Profab Steering Brace, Gibson superflow catback single exhaust system, Locker Bypass, Moog ball joints (see how long they last), New OEM track bar bushings, T-steering upgrade w/ Bilstein 5100 steering damper, Power everything, Heated leather seats, (keeps the better half happy), Rear window defrost, Bilstein 5100 shocks, 35x12.5x17 Toyo AT2 Extremes, Customized H2 alloy wheels, Original rock rails with family friendly steps welded on, Tri fold tonneau, Hi-lift extreme jack, Tool box along with all the essential PW gear. New winch cable, Winch TPS bypass, Cardan joint grease zerk discovery. New front grille assembly. Magnesium Chloride under coating.

If you ever happen to see me running somewhere, you should start running too. :)

User avatar
leo72987
250_Posts
250_Posts
Posts: 492
Joined: Tue Nov 05, 2013 1:38 pm
Location: Ware, MA

Re: 3rd gen u joints

Post by leo72987 » Fri Feb 19, 2016 2:09 pm

This is the information I have gathered over time... I also had a 2005 Power Wagon

Front Driveshaft with AAM 1355 greasable cv

U joint at diff Spicer 5-795x series internal clip comparable to AAM 1344 U-joint AAM Part# 12479126
U Joint CV (2) Spicer 5-3208X series comparable to AAM 1355 U Joint AAM Part# 40085102
CV ball kit can be purchased at Advance

Later Dodge Front driveshafts use AAM 1355 series at all three joints these can be
identified by the external clips.

DO NOT USE SPICER 1330 series joints they may be close but will cuase damage...
2005 Wagon Standard Cab Auto,Bilstein 5100's,White Knuckle Sliders,Dodge Offroad Diff covers,Cooper St Maxx's stock size, Hardwired lockers,Evo manual sway bar disconnect conversion, DT Pro Fab Sway Bar links

gdane4x4
Posts: 20
Joined: Mon Jan 05, 2015 9:32 am

Re: 3rd gen u joints

Post by gdane4x4 » Mon Feb 22, 2016 6:15 am

Thanks guys. Will be looking to order everything this week along with some Balljoints and most likely a free spin kit. Now to decide dynatrac, oem, carli etc etc on Balljoints and then pick a free spin

User avatar
Mr.Smith
1000_Posts
1000_Posts
Posts: 1131
Joined: Wed Sep 04, 2013 6:36 pm
Model Year: 2009
Location: Fort Collins, CO.

Re: 3rd gen u joints

Post by Mr.Smith » Wed Feb 24, 2016 12:11 pm

You may get a better deal ordering all of it straight from Dynatrac...

2011RPW
250_Posts
250_Posts
Posts: 278
Joined: Thu Oct 24, 2013 9:22 pm
Model Year: 2011
Location: Harper, TX

Re: 3rd gen u joints

Post by 2011RPW » Thu Feb 25, 2016 5:16 pm

Dynatrac
2011
Thuren 3" Suspension, 37' Toyo R/T's, S&B, Flowmaster, Diablo Trinity, N-Fab steps (junk), 31" LED Light Bar, Replacement Bumpers, debadged.

Post Reply