Board index General Member Builds

Start your thread and show everyone your build out.

Re: Diesel PW Build Thread

Postby nts007 » Sat Apr 29, 2017 5:47 pm

40x40 with 12' ceiling. 3 doors. 12x10, 10x9 and a 9x7 inside between the workshop and the rest of the area.

I hope I wasn't confusing. I have the wagon frame and chassis still here at home. I'm heading 3.5hrs away to get a reg cab Long box 2500 cummins with no motor or tranny.
Last edited by nts007 on Sat Apr 29, 2017 7:00 pm, edited 1 time in total.
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Re: Diesel PW Build Thread

Postby nts007 » Sat Apr 29, 2017 6:03 pm

I got bored so decided to double up my ditch lights. Only because I had them and they have been sittin for 4 years in their box. But still brand new lol
Attachments
IMG_4674.JPG
IMG_4676.JPG
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Re: Diesel PW Build Thread

Postby nts007 » Sat Apr 29, 2017 6:58 pm

This is what happens when I am actually home on a freaking nice day. Was 14°C today. And practically no wind. So it was a productive day.
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Re: Diesel PW Build Thread

Postby nts007 » Sun Apr 30, 2017 6:04 pm

New project heading for home
Attachments
IMG_4686.JPG
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Re: Diesel PW Build Thread

Postby nts007 » Sun Apr 30, 2017 10:53 pm

Made it home. Big shout out to my new pal billy. It's thanks to him that this project will finally get under way.

Quick spec. 07 2500 ctd reg cab 6spd manual. With no engine or transmission or tcase. All good. I will be starting a separate build thread for this one. And thanks to mikekey and you Moab guys I now have instagram and have uploaded the majority of the progress to date. I will also do the new build in instagram as well. Find me under this username or dpw37.

Now we carry on. Off on another road trip tomorrow.
Attachments
IMG_4695.JPG
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Re: Diesel PW Build Thread

Postby nts007 » Sun May 21, 2017 3:16 pm

Spent time today working on my onboard air setup. I had picked up an air ride compressor and controller awike ago but have done nothin with them. I did all the plumbing today but there was a storm moving in and wind picked up so I didn't get to the wiring or controller.
The way it's set I can either let the pump run the air bags or fill the air tank. Also with the lever adjusted to the tank fill position I can manually fill the bags from the shrader valve. Or fill the air tank from the second shrader valve. The air bags are always in a sealed condition regardless which way the lever is switched. The tank is an old one I've had for years and pretty much had everything i needed to do this with stuff I've collected or bought over the years. The only thing I didn't get to was an air hose quick connect. Which will draw from the air tank only. Hopefully next weekend is good and I can get the test finished up.

I actually started the day planning on doing the leaf spring swap. But after removing the first leaf from the truck I inspected the other leaves and saw that the bushing is really cracked up bad so i put everything back together. Thuren leaves it is. Wife gave me permission if I can sell the old hemi tranny I have here.
Attachments
IMG_4847.JPG
08 ctd--mini max--thuren 3" coils and shackles--4.56 gears and lockers in pw axles--some lights--afe intake system--bd super b turbo--Banks w/m Injection--Dynatrac Balljoints--bilstein 7100s--37" Nitto trail grapplers--DOR Long arms--Carli track bar--Manual T-case swap--Full PW Under armor--PSC Hydro Assist
User avatar
nts007
2000_Posts
 
Posts: 2013
Joined: Wed Dec 11, 2013 9:01 pm
Location: Sask, Canada, Earth

Previous

Return to Member Builds

Who is online

Users browsing this forum: Google [Bot] and 1 guest