Power Wagon Registry

Great idea to post this up

Great job with this stuff! So professional looking!

What does the owner's manual say? Mine says no go. Just asking the obvious. Seems contact with something as the front components are pretty close to inboard side of tire. Manual says rear only for 2500, 2500 Power Wagon, and 3500 SRW. Interestingly it says Front or Rear for 3500 DRW. I can’t imagin...

Yea not sure how a pic of my daughter got in there LOL. Maybe a mod could remove it?

This guy runs them up front (Low_Sky maybe?). Maybe he will chime in with his experience.

I hated bfg’s until I saw video. They’ve won me over from here on out. I've probably gone through 6-7 sets of the BFG ATs (old and new version) over the years. They're good in the snow and have strong sidewalls. Pretty much worthless in mud and wear fairly fast on a PW. I always started to look for...

My 15 Laramie pw seat heater goes on automatically when it’s 42 or lower and the seat ac goes on when it’s warmer than 80. Don’t know how to change those settings. Don’t really care as I like it like that. There are many settings available for the ac air flow and settings. In the main climate contr...

Teaching my daughter mathematics LOL...

DamageWagon wrote: ↑

Sun Dec 01, 2019 12:48 am

You’re having the same noise with all new trans and t case? Either the trans programming is wacky, the shift lever is mis adjusted, or those parts were not replaced.

.... or, it is something else causing the noise....

Sorry to hear about all the stuff you've had to deal with. My '16 has been *very* reliable so far, but I'm also only at 33500 miles. The single biggest source of frustration for me, is the transmission. It's been perfectly reliable for me, but it's so damn clunky and crude.The shifts are smooth in,...

Makes me want to cry. How much do they have it marked up with all of the added awesomeness? Says frame damage was reported... https://www.cargurus.com/Cars/inventorylisting/viewDetailsFilterViewInventoryListing.action?zip=49648&trimNames=Powerwagon&showNegotiable=true&sourceContext=carGurusHomePage...

Makes me want to cry. How much do they have it marked up with all of the added awesomeness? Says frame damage was reported... https://www.cargurus.com/Cars/inventorylisting/viewDetailsFilterViewInventoryListing.action?zip=49648&trimNames=Powerwagon&showNegotiable=true&sourceContext=carGurusHomePage...

might be a long shot, but does anyone have a winch mount that would fit my mega? or know of where I could get one. Emailed a few places with no luck from car-part.com. It doesn't have to be pretty, just functional. I am in lower Michigan Not sure where in lower mi you are, but here is a power wagon...

Whatever BS you need to tell yourself for adjusting the throttle position sensors parameters. :cheers: Well, sure it doesnt add any more power or anything like that, but if the truck FEELS like it has more power and the throttle response is much better and it makes the drive ability of the vehicle ...

Great job, David!!!

LOL!!

Never seen a single drip from mine.

Wheres the water showing up in the cab at?

everyone talks about the d60 but im not all that impressed with what i seen. i guess the huge after market support must be nice but other wise ill stick with the electric cad aam. and fords using some wonky steering stabilizer setup that puts it clear up on the draglink near the pitman arm. brillia...

Yea. You’d mostly likely be better of just regearing your current axles and adding lockers.

My gosh even 35’s almost look small...

Nice truck!

Keep up the good work!

Anybody heard about people having much trouble with the cad in these new trucks?

One of the Moab attendees last year blew his front axle. When he got a new one in he did free spins and had a 13 shaft turned down to fit the axle seal. He now has a non-CAD axle. The free spins aren’t necessary, so you can save a lot of money with just a machined axleshaft. The free spins allow yo...

One of the Moab attendees last year blew his front axle. When he got a new one in he did free spins and had a 13 shaft turned down to fit the axle seal. He now has a non-CAD axle. The free spins aren’t necessary, so you can save a lot of money with just a machined axleshaft. The free spins allow yo...