Power Wagon Registry

PM sent

I have one on my 2014. I used Monsta-Liner on it and removed the piece that shows Go Rhino.You will lose some departure angle as this bumper is wider than the factory bumper. The attachment points aren't as good as they make it sound. The 1" shackle mounts are not the frame attachment points. With t...

HELL YEAH!!! TALK ABOUT WAKING UP A SLEEPING GIANT ! Had I only known about that fuse sooner ! This by-pass is well worth the money. :rockon: I did comparisons with and without the switch flipped. In about 4" of snow climbing ( trying to climb) a hill in 2wd,with nannies engaged truck would not cli...

I had the issue with my '14 and it was a stuck t-stat. I had to convince the dealer-ship though the t-stat was stuck because it didn't show in their trouble shooting.

PM sent

Welcome, Fellow Wyomingite.

Easttnrhino wrote: ↑

Thu Jan 18, 2018 5:30 am

Love the caps on top of corners damage wagon they would also be nice hand holds for us vertical challenged people to climb into bed . How much? How do you get to nuts underneath.

Yes Damage Wagon tell us more.

Easttnrhino wrote: ↑

Sat Nov 11, 2017 8:47 am

Got my skid in, very impressed with work. Most likely be a few days before I get to install (an,t work a bitch).

Still waiting for mine.

Damagewagon , do you have an ETA on the ones that have been ordered? I had a bit of an emergency on the home front on Thursday and that has taken up my time until now. I was able to get back to it today, they will be done in a few days. For the powder coated ones it will be about another 5-8 days. ...

Damagewagon , do you have an ETA on the ones that have been ordered?

I just installed the rear track bar last week on my 2014. IMO money well spent . If you do get one instructions state that there is no need to remove tires,it is a lot easier if you do.

Thanks DamageWagon I will be patiently waiting.

Whats the delivery time on these? This batch is shipping out right away. These are all accounted for. I'll be moving at the end of the month so I won't be making any new parts until the new shop is set up. I'd expect about end of October I'll have more ready to ship out, I'll make a bigger run of p...

So did some measurements today, I think my front bumper is weighing things down. I'm 2 inches on that front bump stop right now with the stock setup. See what happens when I add the Thuren 1.5 inch springs tomorrow. Did you measure to see how much the bumper was weighing it down? I'm considering th...

MikeKey wrote:

TheDirtRoad wrote:Damn dude , mine was nothing that poor !! maybe he used a different welder for mine. I had the one cracked weld.

One too many. You also welded the back.

Yes I did weld the back. Which IMO should have been done initially.
Hey you gonna put some drain holes in the skid plate?

I have Gorilla locks on mine just because I think they are a better lug nut than factory. And Walmart cross-threaded a couple factory lug nuts. Had to change out 1 stud because of it.

Damn dude , mine was nothing that poor !! maybe he used a different welder for mine. I had the one cracked weld.

I like it a lot. Hope he can get them out again. Questions... Fit 1 of my Baja Design Squadrons in the light holes? How much room on top for a S8 (3" deep) or Onx6 (4.39" deep)? Is the fair lead opening bigger than stock? Can't fit a Factor55 Flatlink in the stock opening. I can't answer your quest...

I have Kye Kinzers bumper mounted and I will share my thoughts on it as well. First off if Kye continues to build these bumpers I would highly recommend it . As it is probably the highest clearance, tightest fitting, PW specific bumper out there. Kye did some very impressive engineering on this. I w...

My Kinzer bumper.