Search found 1338 matches

by coder
Thu Sep 17, 2020 11:25 pm
Forum: Power Wagon Talk
Topic: Power Wagon mileage thread
Replies: 28
Views: 1258

Re: Power Wagon mileage thread

190k on my 07
by coder
Fri Sep 04, 2020 12:06 am
Forum: Power Wagon Talk
Topic: AAM ball joints.
Replies: 12
Views: 710

Re: AAM ball joints.

I have Dynatrac ball joints in my truck. After about 140k miles I rebuilt them, tops were still tight bottoms were loose. For about $195 you can get the rebuild kit for all four ball joints and do the work without having to remove them from the axle, very pleased with this product.
by coder
Mon Aug 17, 2020 1:25 pm
Forum: Introductions
Topic: 2013 5.7 PW running like crap...
Replies: 4
Views: 288

Re: 2013 5.7 PW running like crap...

Hello Allgonoshow,

I think you might be right about the cam and the lifters being badly worn or damaged unfortunately the only way to know for sure is to remove them and take a look.
by coder
Mon Aug 10, 2020 11:25 pm
Forum: Power Wagon Talk
Topic: Need help. What does my PW have?
Replies: 19
Views: 763

Re: Need help. What does my PW have?

Code: Select all

https://www.ramtrucks.com/webselfservice/BuildSheetServlet?vin=3D7KS28D35G901197
Add your VIN at the end of the link above and get your build sheet. I tried your VIN and it gives an error, I tried mine and it works fine, please check that the provided VIN is correct and try again.
by coder
Thu Aug 06, 2020 10:02 pm
Forum: Engine & Drivetrain
Topic: 2006 Front Driveshaft Rebuild
Replies: 9
Views: 775

Re: 2006 Front Driveshaft Rebuild

So I got the driveshaft out and pressed out all the joints. Found the bad u-joint that had two ends completely dry 😳. Glad it didn't come apart on me. George at 8lug still the place for spicer joints? Anyone have the part numbers? And any insight on what gets rebuilt on the double cardan? Thanks Go...
by coder
Wed Jul 22, 2020 5:14 pm
Forum: Power Wagon Talk
Topic: 2006 Power Wagon ball joint bore
Replies: 4
Views: 242

Re: 2006 Power Wagon ball joint bore

Those large gash marks look strange, perhaps something was wedged in there to get the ball joints out. The small vertical lines indicate knurled ball joints were previously used so you will need to use them again, smooth sided ball joints won't hold. The install should be fine, if the ball joints ar...
by coder
Fri Apr 24, 2020 1:59 pm
Forum: Power Wagon Talk
Topic: New Tires Yokohama X-AT 35's
Replies: 7
Views: 1315

Re: New Tires Yokohama X-AT 35's

How have you guys been liking the X-AT's? They look like a great solution to an all around tire for these trucks and I like the look. I was wondering how they were performing and if you had done any significant winter driving in them yet. They look like they would do pretty well in snow and ice eve...
by coder
Thu Apr 16, 2020 6:02 pm
Forum: Engine & Drivetrain
Topic: Noticed my 2019 universal joints dont have clips 2019?
Replies: 6
Views: 1517

Re: Noticed my 2019 universal joints dont have clips 2019?

My 07 had the same thing with at least some u-joints, it simplifies manufacturing and saves money for parts suppliers. It does not affect longevity but as mentioned rebuilding them is a pain.
by coder
Sun Mar 29, 2020 10:07 pm
Forum: Member Builds
Topic: 04Ram2500Hemi's Build - 2012 Power Wagon
Replies: 202
Views: 58160

Re: 04Ram2500Hemi's Build - 2012 Power Wagon

Beautiful truck, Raptors are great off road vehicles, go out and put it through its paces then come back give us your feedback and comparison to PW!
by coder
Sun Mar 29, 2020 9:41 pm
Forum: Power Wagon Talk
Topic: 545rfe fill tube grommet question
Replies: 4
Views: 583

Re: 545rfe fill tube grommet question

So what does this actually do?
by coder
Mon Mar 09, 2020 12:29 pm
Forum: Introductions
Topic: New PW owner from California
Replies: 5
Views: 605

Re: New PW owner from California

Nice PW welcome!
by coder
Thu Mar 05, 2020 4:36 pm
Forum: Introductions
Topic: 2020 powerwagon in transit, 1st time RAM owner
Replies: 7
Views: 508

Re: 2020 powerwagon in transit, 1st time RAM owner

HungarianHammer wrote:
Tue Mar 03, 2020 8:18 pm
Stumbled across this forum, excited to be receiving my special order in a few weeks. Just came out of the trim dept and is in transit.
Welcome! What did you order color, options, etc? First time RAM owner, what vehicle are you coming from?
by coder
Tue Feb 18, 2020 7:57 pm
Forum: Engine & Drivetrain
Topic: Lost all gears while driving, transfer case?
Replies: 6
Views: 1000

Re: Lost all gears while driving, transfer case?

Go the truck back on Saturday. Once they got it apart they found that the seal around the pump was leaking, it had been that way for 2-3 years because it made a very slight whining sound, it finally came out and lost all pressure. At 185k miles with nothing ever done to the transmission since 2007 w...
by coder
Tue Feb 11, 2020 8:04 pm
Forum: Engine & Drivetrain
Topic: Lost all gears while driving, transfer case?
Replies: 6
Views: 1000

Re: Lost all gears while driving, transfer case?

Just got the diagnosis the transfer case is fine the transmission pump failed time to get the transmission rebuilt. I have my truck in a reputable shop nearby it should be done late next week.
by coder
Tue Feb 11, 2020 5:36 pm
Forum: Engine & Drivetrain
Topic: Lost all gears while driving, transfer case?
Replies: 6
Views: 1000

Lost all gears while driving, transfer case?

While I was driving down the freeway this morning the engine revved up it went into a free spinning state like neutral and I couldn't shift into any gear. I had to coast to the side of the road and call a tow truck. I can shift through the gears in both the transmission and transfer case but but not...
by coder
Sun Feb 09, 2020 11:39 pm
Forum: Power Wagon Talk
Topic: 2019+/5th Gen Air Dam Removal
Replies: 7
Views: 934

Re: 2019+/5th Gen Air Dam Removal

Looks good it should have come that way from the factory, do those compatibility brackets unbolt and come right off it's hard to tell from the picture?
by coder
Sat Feb 08, 2020 9:20 pm
Forum: Power Wagon Talk
Topic: New Tires Yokohama X-AT 35's
Replies: 7
Views: 1315

Re: New Tires Yokohama X-AT 35's

Pics of the tires
by coder
Sat Feb 08, 2020 8:17 pm
Forum: Power Wagon Talk
Topic: New Tires Yokohama X-AT 35's
Replies: 7
Views: 1315

New Tires Yokohama X-AT 35's

Picked up a new set of tires today Yokohama X-AT's in 35x12.5-17 it's a fairly new Extreme AT tire comparable to the Toyo RT or Nitto Ridge Grappler take a look.

https://www.yokohamatire.com/tires/geolandar-x-at
by coder
Sat Feb 08, 2020 7:26 pm
Forum: Engine & Drivetrain
Topic: 14+ Possible Fan Clutch failure?
Replies: 19
Views: 1578

Re: 14+ Possible Fan Clutch failure?

Here is an easy way to tell if your fan clutch is working correctly or not: 1) The fan clutch should stop spinning almost immediately when you shut the engine off, if it keep spinning the clutch is worn out. 2) With the engine off you should be able to turn the fan by hand, if not the clutch is lock...
by coder
Wed Nov 27, 2019 11:46 am
Forum: Power Wagon Talk
Topic: 3 Gen Stainless SRT Exhaust Stud/Bolt PNs?
Replies: 8
Views: 1050

Re: 3 Gen Stainless SRT Exhaust Stud/Bolt PNs?

:rockon: coder :rockon: I hope you get many years before you hear tick-tick-tick-tick-tick again :D Thanks I hope so too. The funny thing is didn't really hear the tick-tick-tick of a leak I only noticed that my right side exhaust heat-shield was rattling around after further inspection I found tha...
by coder
Tue Nov 26, 2019 7:58 pm
Forum: Power Wagon Talk
Topic: 3 Gen Stainless SRT Exhaust Stud/Bolt PNs?
Replies: 8
Views: 1050

Re: 3 Gen Stainless SRT Exhaust Stud/Bolt PNs?

I ended up replacement everything with new OEM parts including studs/bolts, gaskets and heat-shields. I had one broken stud that needed to be extracted the nuts holding the heat-shields on were rusted solid so they had to be cut off. I could not get the right side header out of the wheel well so I d...
by coder
Mon Nov 11, 2019 9:47 pm
Forum: Power Wagon Talk
Topic: 3 Gen Stainless SRT Exhaust Stud/Bolt PNs?
Replies: 8
Views: 1050

3 Gen Stainless SRT Exhaust Stud/Bolt PNs?

After 3 year and 40k miles I need to replace the exhaust manifold studs/bolts on my trucks rebuilt engine. I have heard that you can use stainless steel SRT bolts. Are there any negatives in doing this, does anyone have the part numbers? Any and all input is welcome.
by coder
Sat Oct 19, 2019 12:08 am
Forum: Power Wagon Talk
Topic: I still like this truck.
Replies: 12
Views: 1945

Re: I still like this truck.

Beautiful country perfect PW territory
by coder
Fri Oct 18, 2019 11:53 pm
Forum: Power Wagon Talk
Topic: Fun in Telluride
Replies: 5
Views: 864

Re: Fun in Telluride

Great pics nice to see a PW being enjoyed in the backcountry!
by coder
Tue Oct 15, 2019 7:14 pm
Forum: Power Wagon Talk
Topic: Transfer case fill plug
Replies: 3
Views: 462

Re: Transfer case fill plug

Same thing happened to me last year I purchased a Hanson 53211 Extractor (7/16" Multi Spline, for Tap Die Extraction) with a 5/8 socket it came out in a few minutes got 2 new plugs (fill & drain) from the dealer PN 68001627AA . Extractor How To Video: https://youtu.be/HoxQQuRHWd0 Amazon Link For Han...